Low price for Bs3076 Na18 - Alloy 50 (aka Magnifer 50, Carpenter High Permeability 49, Alloy 47-50) – Herui

Low price for Bs3076 Na18 - Alloy 50 (aka Magnifer 50, Carpenter High Permeability 49, Alloy 47-50) – Herui Featured Image
  • Low price for Bs3076 Na18 - Alloy 50 (aka Magnifer 50, Carpenter High Permeability 49, Alloy 47-50) – Herui

Short Description:


Product Detail

HOW TO USE THE SAWBLADE

Product Tags

Related Video

Feedback (2)

We have been ready to share our knowledge of internet marketing worldwide and recommend you suitable merchandise at most aggressive rates. So Profi Tools present you very best price of money and we are ready to develop alongside one another with Molybdenum High Speed Steel , Compressor Capillary Tube , Delayed Expansion In Amalgam , Wanting on the long run, a protracted way to go, continually striving to become the all team with full enthusiasm, one hundred times the confidence and put our company created a beautiful environment, advanced merchandise, good quality first-class modern business and get the job done hard!
Low price for Bs3076 Na18 - Alloy 50 (aka Magnifer 50, Carpenter High Permeability 49, Alloy 47-50) – Herui Detail:

Description

A soft magnetic alloy, consisting of 49% Nickel, balance Iron used where high initial permeability, maximum permeability, and low core loss is needed.

Chemical Composition

C P S Cu Mn Si Ni Fe
≤
0.03 0.020 0.020 0.20 0.30-0.60 0.15-0.30 49.0-50.5 Balance

Characters

High permeability

High magnetic flux density

Good fabrication property 

Anti-rust ability

Applications

Small power transformers, micro motors, relays, choke ring and an electromagnetic clutch of core, and magnetic shield of the microphone diaphragm torque motor armature and a conducting magnet.

Equal Grades

1J50(China), 50H(Russia), PB(Japan)

Forms available

Strip, bar, wire

Product detail pictures:

Low price for Bs3076 Na18 - Alloy 50 (aka Magnifer 50, Carpenter High Permeability 49, Alloy 47-50) – Herui detail pictures

Related Product Guide:
We persist with the principle of "quality 1st, assistance initially, continual improvement and innovation to meet the customers" for your management and "zero defect, zero complaints" as the standard objective. To great our service, we present the products and solutions while using the very good top quality at the reasonable cost for Low price for Bs3076 Na18 - Alloy 50 (aka Magnifer 50, Carpenter High Permeability 49, Alloy 47-50) – Herui, The product will supply to all over the world, such as: Moscow, Qatar, Buenos Aires, As the world economic integration bringing challenges and opportunities to the xxx industry, our company , by carrying on our teamwork, quality first, innovation and mutual benefit, are confident enough to provide our clients sincerely with qualified products, competitive price and great service, and to build a brighter future under the spirit of higher, faster, stronger with our friends together by carrying on our discipline.
The use and maintain of the sawblade

◎ The carbide tip of sawblade is very sharp, so process of using must be prevent the carbide tip.

◎ PeriodicaI cleaning and support the machine,the spindle’s running tolerance must be less than h7.

◎ The flanges must be parallel to each other,must be of the same diameter 1/3 of the sawblade’s diameter(formuIti—rip saw blade is 1/2.

◎ When instaIIion the sawbIade,it shaII be 5-6 teeth higher than board surface．

◎ Before operation,check the firmly of the sawblade,be sure nobody in front of the machine. Do not feed of operation check whether the machine is good for operaiton. Periodical check the function of the machine,the certicaI jump is less than ±0.02MM,and the flap is less than ±0.01.

◎ After continuous use,must be removed and cleaning the sawblade,get rid of the resin and sawdust of the sawblade of both sides.Other wise it would beinfluence the effect of using the sawblade.

◎ Deposit of the sawblade,must not be layer the sawblade,it is putted in the originaI package inside.

The renovate of the sawbIade

◎ The renovate of the carbide sawblade While it no longer sharpen and the horizontaI piece coarseaess. The power of using sawblade machine obviously Increase. When process materiaI,the materiaI appearred burst. The carbide tip exhaust more than 0.02MM.

◎ For the renovate the sawblade,it shouId be grinding by the a formal company, so be sure the quality of the sawblade after renovating.

    • Product quality is good, quality assurance system is complete, every link can inquire and solve the problem timely!
    5 Stars By Juliet from Macedonia - 2018.11.04 10:32
    This is a honest and trustworthy company, technology and equipment are very advanced and the prodduct is very adequate, there is no worry in the suppliment.
    5 Stars By Carol from Philadelphia - 2018.05.22 12:13

    RELATED PRODUCTS