Top Quality Capillary Tube Of Thermometer - Alloy 52 (aka Pernifer 50, NILO 50, Glass Seal 52) – Herui Detail:
Description
A controlled expansion alloy, consisting of 51% Nickel, balance Iron, used in a wide variety of electronic applications, especially for glass seals. Alloy 52 is a nickel iron alloy whose coefficient of expansion closely mirrors soft glass. Applications for this product include magnetic reed switches and seals that need controlled linear expansion to approximately 525 °C.
Alloy 52 Basic Chemical Composition (Weight %)
| Ni | 50.50 |
| Cr | 0.10 max |
| Mn | 0.60 max |
| Si | 0.30 max |
| C | 0.05 max |
| Al | 0.10 max |
| Mg | 0.50 max |
| P | 0.025 max |
| S | 0.025 max |
| Fe | Balance |
Typical Mechanical Properties
|
Alloy 52 |
Annealed |
As Rolled |
|
Ultimate Tensile Strength (PSI) |
75,000 |
130,000 |
|
Yield Strength (PSI) |
30,000 |
125,000 |
|
Elongation |
30% |
1% |
|
Modulus of Elasticity (PSI) |
24 x 10e6 |
|
|
Poisson’s Ratio |
0.29 |
|
Typical Physical Properties
Density 0.300 lbs/cu in
Melting Point 1425° C
Electrical Resistivity @ RT 43 Microhm-cm
Temp. Coefficient Resistivity 2900 PPM/°C
(20 to 100° C)
Thermal Expansion Coefficient 10.0 x 10e-6/°C
(30 to 400° C)
Applications
Glass to metal seals for electronic tubes, automotive and industrial lamps, and specialty hermetic devices.
Available Forms
Alloy 52 is available in Strip, Sheet, Plate and Wire.
Product detail pictures:
Related Product Guide:
Our mission is usually to turn into an innovative provider of high-tech digital and communication devices by furnishing benefit added design and style, world-class manufacturing, and service capabilities for Top Quality Capillary Tube Of Thermometer - Alloy 52 (aka Pernifer 50, NILO 50, Glass Seal 52) – Herui, The product will supply to all over the world, such as: Jordan, Swansea, Indonesia, Our items have national accreditation requirements for qualified, high quality products, affordable value, was welcomed by people today all over the world. Our goods will continue to enhance within the order and look forward to cooperation with you, Should any of these products be of interest to you, please letus know. We are going to be content to offer you a quotation up on receipt of your detailed needs.
The use and maintain of the sawblade
◎ The carbide tip of sawblade is very sharp, so process of using must be prevent the carbide tip.
◎ PeriodicaI cleaning and support the machine,the spindle’s running tolerance must be less than h7.
◎ The flanges must be parallel to each other,must be of the same diameter 1/3 of the sawblade’s diameter(formuIti—rip saw blade is 1/2.
◎ When instaIIion the sawbIade,it shaII be 5-6 teeth higher than board surface．
◎ Before operation,check the firmly of the sawblade,be sure nobody in front of the machine. Do not feed of operation check whether the machine is good for operaiton. Periodical check the function of the machine,the certicaI jump is less than ±0.02MM,and the flap is less than ±0.01.
◎ After continuous use,must be removed and cleaning the sawblade,get rid of the resin and sawdust of the sawblade of both sides.Other wise it would beinfluence the effect of using the sawblade.
◎ Deposit of the sawblade,must not be layer the sawblade,it is putted in the originaI package inside.
The renovate of the sawbIade
◎ The renovate of the carbide sawblade While it no longer sharpen and the horizontaI piece coarseaess. The power of using sawblade machine obviously Increase. When process materiaI,the materiaI appearred burst. The carbide tip exhaust more than 0.02MM.
◎ For the renovate the sawblade,it shouId be grinding by the a formal company, so be sure the quality of the sawblade after renovating.
By Nainesh Mehta from Tunisia - 2018.09.23 17:37
The product classification is very detailed that can be very accurate to meet our demand, a professional wholesaler.
By EliecerJimenez from St. Petersburg - 2018.12.11 14:13
