Nickel Series

  • Corrosion-resistant Copper-nickel Alloy Monel K-500 Sheet

    Corrosion-resistant Copper-nickel Alloy Monel K-500 Sheet

    MONEL alloy K-500 (UNS N05500 / W. Nr. 2.4375) is a nickel-copper alloy which combines the excellent corrosion resistance of MONEL alloy 400 with the added advantages of greater strength and hardness. The increased properties are obtained by adding aluminum and titanium to the nickel-copper base, and by heating under controlled conditions so that submicroscopic particles of Ni3 (Ti, Al) are precipitated throughout the matrix. The thermal processing used to effect precipitation is commonly called age hardening or aging. Typical applications for MONEL K-500 products are chains and cables, fasteners and springs for marine service; pump and valve components for chemical processing; doctor blades and scrapers for pulp processing in paper production; oil well drill collars and instruments, pump shafts and impellers, non-magnetic housings, safety lifts and valves for oil and gas production; and sensors and other electronic components.

  • Heat and Corrosion Resistance UNS N07750 Inconel X-750 Spring Wire

    Heat and Corrosion Resistance UNS N07750 Inconel X-750 Spring Wire

    Inconel X-750 (UNS N07750 / W. Nr. 2.4669 / GH4145 / NiCr15Fe7TiAl) is a precipitation-hardenable nickel-chromium alloy used for its corrosion and oxidation resistance and high strength at temperatures to 1300°F. Although much of the effect of precipitation hardening is lost with increasing temperature over 1300°F, heat-treated material has useful strength up to 1800°F. This kind of alloy also has excellent properties down to cryogenic temperatures. 

  • Alloy 50 (aka Magnifer 50, Carpenter High Permeability 49, Alloy 47-50)

    Alloy 50 (aka Magnifer 50, Carpenter High Permeability 49, Alloy 47-50)

    Description A soft magnetic alloy, consisting of 49% Nickel, balance Iron used where high initial permeability, maximum permeability, and low core loss is needed. Chemical Composition C P S Cu Mn Si Ni Fe ≤ 0.03 0.020 0.020 0.20 0.30-0.60 0.15-0.30 49.0-50.5 Balance Characters High permeability High magnetic flux density Good fabrication property  Anti-rust ability Applications Small power transformers, micro motors, relays, choke ring and an electromagnetic clutch of core, and magn...
  • Alloy 52 (aka Pernifer 50, NILO 50, Glass Seal 52)

    Alloy 52 (aka Pernifer 50, NILO 50, Glass Seal 52)

    Description A controlled expansion alloy, consisting of 51% Nickel, balance Iron, used in a wide variety of electronic applications, especially for glass seals. Alloy 52 is a nickel iron alloy whose coefficient of expansion closely mirrors soft glass. Applications for this product include magnetic reed switches and seals that need controlled linear expansion to approximately 525 °C. Alloy 52 Basic Chemical Composition (Weight %) Ni  50.50 Cr  0.10 max Mn  0.60 max Si  0.30 max C  0...
  • Monel K-500

    Monel K-500

    Description MONEL alloy K-500 (UNS N05500 / W. Nr. 2.4375) is a nickel-copper alloy which combines the excellent corrosion resistance of MONEL alloy 400 with the added advantages of greater strength and hardness. The increased properties are obtained by adding aluminum and titanium to the nickel-copper base, and by heating under controlled conditions so that submicroscopic particles of Ni3 (Ti, Al) are precipitated throughout the matrix. The thermal processing used to effect precipitation is ...
  • NIMONIC 80A

    NIMONIC 80A

    Description NIMONIC alloy 80A (UNS N07080/W. Nr. 2.4952 & 2.4631) is a wrought, age-hardenable nickel-chromium alloy, strengthened by additions of titanium, aluminum and carbon, developed for service at temperatures up to 815°C (1500°F). It is produced by high-frequency melting and casting in air for forms to be extruded. Electroslag refined material is used for forms to be forged.  Vacuum refined versions are also available. NIMONIC alloy 80A is currently used for gas turbine components ...
  • NIMONIC 90

    NIMONIC 90

    Description NIMONIC 90 (UNS N07090/W. Nr. 2.4632) is a wrought nickel-chromium-cobalt base alloy strengthened by additions of titanium and aluminum. It has been developed as an age-harden-able creep-resisting alloy for service at temperatures up to 920°C (1688°F. The alloy is used for turbine blades, discs, forgings, ring sections and hot-working tools. Typical chemical composition Carbon  0.13 max. Silicon  1.0 max. Copper  0.2 max. Iron  1.5 max. Manganese  1.0 max. Chromium  1...
  • Pure Nickel

    Pure Nickel

    Description Commercially pure or low-alloy nickel has characteristics that are useful in several fields, notably chemical processing and electronics. Pure Nickel is highly resistant to various reducing chemicals and is unexcelled in resistance to caustic alkalis. Compared with nickel alloys, commercially pure nickel has high electrical and thermal conductivity. It also has a high Curie temperature and good magnetostrictive properties. Annealed nickel has a low hardness and good ductility and ...
  • Techalloy 606 Welding AWS 5.14 MIG ERNiCr-3 Wire

    Techalloy 606 Welding AWS 5.14 MIG ERNiCr-3 Wire

    Description Commercially pure or low-alloy nickel has characteristics that are useful in several fields, notably chemical processing and electronics. Pure Nickel is highly resistant to various reducing chemicals and is unexcelled in resistance to caustic alkalis. Compared with nickel alloys, commercially pure nickel has high electrical and thermal conductivity. It also has a high Curie temperature and good magnetostrictive properties. Annealed nickel has a low hardness and good ductility and ...
  • Inconel 718

    Inconel 718

    Description Inconel 718 (UNS N07718 / W. Nr. 2.4668 / GH4169 / NiCr19Fe19Nb5) is a high-strength, corrosion-resistant nickel chromium material used at -423° to 1300°F. The age-hardenable alloy can be readily fabricated, even into complex parts. Its welding characteristics, especially its resistance to post-welding cracks, are outstanding. The ease and economy with which INCONEL alloy 718 can be fabricated, combined with good tensile, fatigue, creep, and rupture strength, have resulted in its ...
  • ERNiCrMo-3

    ERNiCrMo-3

    Keywords: Inconel 625, AWS A5.14, EN18274, ASME II, SFA-5.14, EN/RN625, Nickel Alloy Welding Wire Chemical composition Gr. No. % Ni Cr Mo Nb+N Fe Al Ti C Mn Si Cu P S Inco 625 Min Bal. 20 8 3.15                   Max   23 10 4.15 5 0.4 0.4 0.1 0.5 0.5 0.5 0.015 0.015 Pysical properties Density 8.4 g/cm³ Melting Point 1290-1350°C Inconel 625 Alloy minimum mechanical properties in the room temperature Tensile Strength Yield Strength Elongation Brinell Hardness ...
  • Alloy 800 (UNS N08800), Alloy 800H (UNS N08810), and Alloy 800HT (UNS N08811) 

    Alloy 800 (UNS N08800), Alloy 800H (UNS N08810), and Alloy 800HT (UNS N08811) 

    Description Alloy 800 (UNS N08800, NS111), Alloy 800H (UNS N08810, NS112), and Alloy 800HT (UNS N08811) are nickel-iron-chromium alloys designed to resist oxidation and carburization at elevated temperatures. The nickel content, 32%, makes the alloys highly resistant both to chloride stress-corrosion cracking and to embrittlement from precipitation of sigma phase. The general corrosion resistance is excellent. In the solution annealed condition, Alloys 800H and 800HT have superior creep and s...
12345 Next > >> Page 1 / 5